Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Before
After
Before
After
Before
AfterOlympia Chimney Chimney Cap & Crown in Wakefield: What to Know First
As an independent Olympia Chimney service provider, we handle cap installation, cap replacement, crown repair, and crown coating on Olympia Chimney systems throughout Wakefield. Most Olympia Chimney cap and crown jobs run $280-$780 depending on whether we’re fitting a stock multi-flue cap or rebuilding a deteriorated crown, and we typically schedule within a week during peak season. We don’t quote over the phone for crown work - every estimate starts with a camera inspection so you see what we see, and the price we give is the price on the invoice.
This page is for Wakefield homeowners who already have an Olympia Chimney liner, cap, or venting component and need someone who knows how these products age in Essex County weather. If your cap is rattling in a nor’easter, your crown is shedding mortar, or you’re not sure whether the rust is cosmetic or structural, call us at (857) 364-8219. A live person answers, 24 hours a day.
How Olympia Chimney Products Fail - and How We Fix Them
- Olympia Chimney 316Ti stainless caps: The mesh on these caps is finer than standard galvanized units, which is good for keeping out Wakefield’s cottonwood seed and pine pollen, but the welds at the corner seams can fatigue after 8-12 winters of freeze-thaw. We see this especially on homes near Lake Quannapowitt where morning fog accelerates surface corrosion. Our fix: inspect the weld integrity with a camera before recommending replacement. If the frame is sound, we can source a direct-fit Olympia mesh replacement rather than swapping the entire cap.
- Olympia Chimney multi-flue caps (galvanized and stainless): These ship with a standard 10-inch skirt height, which is adequate for most installations but can be short for Wakefield’s deeper-set flue tiles in 1920s colonials and capes. Water pools at the flue edge, freezes, and pushes the cap upward. We spot this during pre-installation measurement and fabricate a taller skirt or build up the flue surround with crown coating so the cap seats properly.
- Olympia Chimney Gelco-compatible caps: Olympia’s relationship with Gelco means many of their caps use Gelco’s mounting hardware, but the bolt patterns changed slightly around 2016. Homeowners who order their own “Gelco replacement” online often get hardware that doesn’t mate to pre-2016 Olympia bases. We carry both bolt patterns and the transition brackets, so we don’t leave you with a cap that can’t be secured.
- Olympia Chimney crown coating failures: Olympia distributes a crown sealant that’s flexible and UV-stable, but it’s often applied too thin by homeowners or general handymen. In Wakefield’s climate, a thin coat cracks by year three. We strip failed coating back to sound concrete, apply a slurry bond coat, then build to 3/8-inch minimum thickness with proper taper for runoff. The chimney either works or it doesn’t. We make sure it does.
- Olympia Chimney wind-load issues on raised-frame caps: The Olympia raised-frame design with elevated lid performs well for draft, but the taller profile catches wind coming off the Breakheart Reservation hills. We’ve replaced three in the past two years where the mounting straps fatigued from vibration. We now upgrade to through-bolt mounting with expansion anchors on these specific installations, not just strap tension.
Our Olympia Chimney Chimney Cap & Crown Process
- 1
Call and schedule. A live person answers, day or night. We book a Level-2 camera inspection - not a sales visit, a real diagnostic with photos you can see and a plain-English verdict.
- 2
On-site inspection. Our tech documents cap or crown condition, flue tile height, and surrounding masonry. For Olympia Chimney systems, we note the series marking (usually stamped on the cap frame or liner collar) so we source correct parts.
- 3
Parts decision. If OEM Olympia Chimney components are available with reasonable lead time, we present that option. If the job calls for faster turnaround or the OEM part has been superseded, we specify quality aftermarket from Gelco, Famco, or Copperfield that matches Olympia’s dimensions and won’t void any remaining liner warranty.
- 4
The repair. Cap installations get proper mounting: straps for standard duty, through-bolts for wind-exposed or raised-frame units. Crown repairs get stripped to sound substrate, rebuilt with proper slope and thickness, then sealed. No shortcuts.
- 5
Post-work test and documentation. We run a visual camera pass to confirm clear flue, proper cap clearance, and no debris from the job. You get photos, a written summary, and the 90-Day Done Right Promise in writing.
- 6
Cleanup and closeout. Background-checked, uniformed techs leave the roof and yard as found. Most Olympia Chimney cap and crown jobs complete in a single visit. The number on the estimate is the number on the invoice.
What Olympia Chimney Chimney Cap & Crown Costs in Wakefield
| Service | Typical Range | What Moves the Price |
|---|---|---|
| Olympia Chimney cap installation (single flue, stock size) | $280-$420 | Flue height, need for spark arrestor, roof pitch |
| Olympia Chimney multi-flue cap replacement | $480-$680 | Custom skirt height, stainless vs. galvanized, wind-load hardware |
| Crown coating (sound base, preventive) | $340-$480 | Crown square footage, number of flue penetrations |
| Crown rebuild / partial pour (deteriorated base) | $620-$1,180 | Extent of concrete removal, need for formwork, flue tile reset |
| Raised-frame cap with through-bolt upgrade | $580-$780 | Anchor depth into masonry, custom flashing integration |
These are Wakefield market ranges for Olympia Chimney-compatible work using professional-grade materials - not builder-grade substitutes. A $50 discount applies to any repair over $250. Seniors and veterans save 5% on every job, every day.
Call (857) 364-8219 for an exact quote. Estimates are free, and we don’t recommend work without camera evidence you can see for yourself.
Why Wakefield Homeowners Call Hearthstone Chimney Co. for Olympia Chimney Work
We’ve been answering the phone with a live person for over 42 years, and we’ve been working Wakefield long enough to know which cap designs hold up on the older homes near the lake and which don’t. Russell Haines and our crew have replaced Olympia Chimney caps that failed from correctable installation errors - wrong skirt height, wrong hardware, wrong assumptions about New England wind.
Our Level-2 inspections end with photos and a plain-English verdict, documented like an engineer, explained like a craftsman. The 90-Day Done Right Promise means if it’s not right, we make it right - in writing, no arguing, no paperwork chase. We also work with DuraFlex, HeatShield, and Gelco systems, so if your Olympia Chimney component interfaces with another brand, we don’t guess at the connection.
Done right - and we stand behind it. We’ll be there when we say.
FAQs
No, as an independent Olympia Chimney service provider, our cap and crown work does not void manufacturer warranties on liners or venting components, provided we use compatible parts and proper installation methods. We document our work with photos in case any warranty question arises later. Call (857) 364-8219 if you have a specific warranty concern.
Most single-flue and multi-flue cap replacements on Olympia Chimney systems finish in 2-3 hours, including removal, flue inspection, and proper mounting. Crown rebuilds take longer - typically a half day - because the concrete needs proper cure time before we seal. We complete most jobs in a single visit. Call (857) 364-8219 to schedule.
If the crown has cracks but the concrete is sound underneath, coating is appropriate and cost-effective. If the crown is spalling, crumbling, or leaking into the masonry below, coating over it wastes your money - we rebuild first, then seal. Our camera inspection shows you which situation you have. Call (857) 364-8219 for a free look.
Common Olympia Chimney cap sizes and hardware are in our regular supplier rotation, usually 3-5 business days if not in stock. For older or specialized sizes, we also source compatible aftermarket from Gelco, Famco, or Copperfield that matches Olympia’s specifications. We don’t leave you waiting indefinitely for a back-ordered part when a quality equivalent exists.
Rattling in wind often means loose mounting straps or a cap that’s lifted from freeze-thaw pressure - both let water in. Rust streaks on the chimney face mean the cap mesh or lid is corroding through. Water in the firebox after rain is a definitive sign. We can confirm with a camera inspection; if the cap is sound, we’ll tell you it’s sound. Call (857) 364-8219.
Written by Russell Haines, Owner & Master Sweep, Hearthstone Chimney Co. at Hearthstone Chimney Co., serving Wakefield and nearby areas.